Results 1 to 18 of 18

Thread: Running Rich, Carbureted 98 ZX6R

  1. #1
    Junior Member BrianShaw's Avatar
    Join Date
    Apr 2013
    Location
    Aurora, CO
    Posts
    41

    Running Rich, Carbureted 98 ZX6R

    Ok, My Ninja is running a bit rich.
    I changed the plugs and cleaned the airfilter without any real change.

    (It was back firing on me, not all the time, but when it did it was bad, the spark plug on the number 1 cylinder seemed loose)

    As it is warming up outside, (I have had this bike about a month), it is getting harder and harder to start.
    A lot of fuel smell, IE make sure your in a well ventilated area.

    How should I try to correct this issue.
    Drop the jet size, but by how much?
    1 size, 2 sizes?

    Maybe just get an aftermarket slip-on to lean it out? Currently it is running the stock can?

    It started pretty easy when it was 40 degrees or colder outside, but now that it is warming up it is getting pretty difficult to start. Even if it is all ready warmed up.

    Also, If I try to ride it without it fully warmed up, it backfires and or stalls on me.

    Thanks,
    1998 Kawasaki ZX6R
    1973 Honda CL350 Cafe
    sold- 1978 Honda CB750 SuperSport
    sold- 2004 BMW R115R

  2. #2
    Senior Member longrider's Avatar
    Join Date
    Sep 2003
    Location
    Elizabeth
    Posts
    1,813

    Re: Running Rich, Carbureted 98 ZX6R

    What did you oil the filter with? I had a 98 ZX7 and used air filter oil like on dirt bikes and it ran so rich it would not rev over about 6K. Rewashed the filter and used 10-40 motor oil like Kawasaki specifies and it ran great. You do need to squeeze all the oil out that you can (I am assuming the 6 uses a foam filter like the 7)

  3. #3
    Junior Member BrianShaw's Avatar
    Join Date
    Apr 2013
    Location
    Aurora, CO
    Posts
    41

    Re: Running Rich, Carbureted 98 ZX6R

    It was running rich, so I skipped the oil for now. Just cleaned it. Yes it is a foam filter, black on one side, yellow on the other.
    1998 Kawasaki ZX6R
    1973 Honda CL350 Cafe
    sold- 1978 Honda CB750 SuperSport
    sold- 2004 BMW R115R

  4. #4
    Member
    Join Date
    Mar 2011
    Posts
    356

    Re: Running Rich, Carbureted 98 ZX6R

    If the carb is stock, it would be pretty unusual it would be that rich at our altitude considering they are jetted slightly lean at sea level. Maybe it's a different problem like with your float since you are smelling gas.

  5. #5
    Junior Member BrianShaw's Avatar
    Join Date
    Apr 2013
    Location
    Aurora, CO
    Posts
    41

    Re: Running Rich, Carbureted 98 ZX6R

    I am not sure, could be anything:Float, air/fuel mixture setting, needle position or just need to be cleaned. I just wish I knew a little more about these carbs and how to set them up.
    1998 Kawasaki ZX6R
    1973 Honda CL350 Cafe
    sold- 1978 Honda CB750 SuperSport
    sold- 2004 BMW R115R

  6. #6
    Junior Member BrianShaw's Avatar
    Join Date
    Apr 2013
    Location
    Aurora, CO
    Posts
    41

    Re: Running Rich, Carbureted 98 ZX6R

    Started backfiring/sputtering again this morning when it was under load. Untill it would stall. If I let off the gas and pull the clutch it would stay running. Seems to come on and start happening for no appearant reason.

    I am going to pull the carbs tonight, clean them up, change the fuel filter, and probably drop the main jet size, a size or two.

    When I start the bike now, I have to hold the throttle open to get it started. IE getting more air through the carbs. So it acts like it is always flooded when starting.

    It is now getting to the point where it is getting dangerous to ride.
    1998 Kawasaki ZX6R
    1973 Honda CL350 Cafe
    sold- 1978 Honda CB750 SuperSport
    sold- 2004 BMW R115R

  7. #7
    Member Yearly Supporter rifleshooter's Avatar
    Join Date
    Dec 2012
    Location
    Frederick, CO
    Posts
    172

    Re: Running Rich, Carbureted 98 ZX6R

    Constant velocity carbs?

    Air leak causing an mixture problem? Air hoses installed correctly?

  8. #8
    Junior Member BrianShaw's Avatar
    Join Date
    Apr 2013
    Location
    Aurora, CO
    Posts
    41

    Re: Running Rich, Carbureted 98 ZX6R

    I am going to pull the tank back off tonight, I will be able to check them again. But when I had it off to change the plugs, all the Air hoses looked to be securely in place. I seem to be working with a lot of random. I have not even found the default baseline settings for the carbs yet.
    1998 Kawasaki ZX6R
    1973 Honda CL350 Cafe
    sold- 1978 Honda CB750 SuperSport
    sold- 2004 BMW R115R

  9. #9
    Member
    Join Date
    Mar 2011
    Posts
    356

    Re: Running Rich, Carbureted 98 ZX6R

    Make sure to sync the carbs too when you're done.

  10. #10
    Senior Member FZRguy's Avatar
    Join Date
    Feb 2003
    Location
    Lakewood
    Posts
    4,476

    Re: Running Rich, Carbureted 98 ZX6R

    Changing just the main jets will not do much for idle thru mid-range RPM. Invest in a jet kit and a service manual.

    http://www.dynojet.com/jetkits/motorcycle/kawasaki.aspx

    Unless someone has changed them, they are CV carbs. Read below on how to tune CV carbs, or take it to a pro like Jim at TFOG.

    BTW, running a foam filter dry is no bueno. The filter needs oil to trap dust and dirt. I like No Toil oil and cleaner. It cleans up easy with the cleaner and water, and is bio-degradable.
    Last edited by FZRguy; Fri May 17th, 2013 at 02:28 AM.
    John
    KTM Duke 690

  11. #11
    Senior Member FZRguy's Avatar
    Join Date
    Feb 2003
    Location
    Lakewood
    Posts
    4,476

    Re: Running Rich, Carbureted 98 ZX6R

    Below is a great article by Marc Salvisberg of Factory Pro on how to tune CV carbs.


    CV Carb Tuning
    High RPM engines

    Have a website? Want to provide tuning information?
    Please do not plagiarize this page - it took years to develop and write and is not based on any other previous work by anybody else. If you want to link to this page on your site, please ask - we are perfectly willing to allow links as long as proper credit is provided. Thanks - Marc

    Follow steps in order....First dial in:

     1. Top end (full throttle / 7.5k to redline -
    Best Main Jet must be selected before starting step 2 (needle height)!
     Select Best Main Jet
     To get the best, most even top end power (full throttle/after 7500 rpm), select the main jet that produces the highest top speed / pulls hardest at high rpm.
     If the bike pulls harder at high rpm when cold and less hard when fully warmed up, the main jet is too large. Install a smaller main jet and retest until you find the main jet that pulls the hardest at high rpm when fully warmed up. This must be done first - before moving on to the other tuning ranges.
     If the bike doesn't pull well at high rpm when cold and gets only slightly better when fully warmed up, the main jet is too small.
     In order to properly tune the midrange and low rpm carburetion, THE MAIN JET MUST FIRST BE PROPERLY SELECTED after 10 to 15 minutes of hard use!
     Do not pay too much attention to the low-end richness when you are changing main jets - you still need to be using the main jets that produce the best power at high rpm. You will deal with the low-end / cruise later - after step 2.

     2. Midrange (full throttle /5k-7k)
    Step 1 (Best Main Jet) must be selected before starting step 2!
     Select best needle clip position
     To get the best power at full throttle / 5k-7k rpm, adjust the needle height, after you have already selected the best main jet.
     If the engine pulls better or is smoother at full throttle/5k-7k in a full throttle roll-on starting at <3k when cool but soft and/or rough when at full operating temperature, it is too rich in the midrange and the needle should be lowered.
     If the engine pulls better when fully warmed up but still not great between 5k-7k, try raising the needle to richen 5k-7k.
     If the engine pulls equally well between 5k-7k when cooler as compared to fully warmed up, the needle height is probably properly set.
     Do not pay too much attention to the low-end richness when you are changing needle clip positions - you still need to be using the clip position that produces the best full throttle / 5k-7k power in conjunction with the main jets (Step 1) that produce the best power at high rpm. You will deal with the low-end / cruise next.

     3. Low end (full throttle / 2k-3k)
    Step 1 (Best Main Jet) and Step 2 (needle height) must be selected before starting step 3!
     Float height (AKA fuel level & how to..)
     To get best low-end power, set float height (fuel level) so that the engine will accept full throttle, without missing or stumbling, in 2nd gear from 2.5k to 3k rpm at minimum.
     Float heights, unless otherwise specified in the installation guide, are measured from the "gasket surface" of the carb body to the highest part of the top of the float - with the float tang touching but not compressing the float valve spring.
     If the engine has a "wet" rhythmic, soggy area at full throttle / 3k-4k rpm, that gets worse as the engine heats up, lower the fuel level by resetting the float height 1mm greater (if the original was 13mm - go to 14mm). This will lower the fuel level, making full throttle / 2k-3k rpm leaner.
     If the engine is "dry" and flat between 2k to 3k rpm, raise the fuel level.
     Example: change float height from 15mm to 14mm to richen up that area.
     REMEMBER, since the main jet WILL affect low speed operation, the MAIN JET has to be within 1 or 2 sizes of correct before final float setting.
     Warning: If the engine is left with the fuel level too high,, the engine may foul plugs on the street and will be "soft" and boggy at part throttle operation. Adjust Floats to raise/ lower the Fuel Level.
     Base settings are usually given if a particular application has a history of fuel level criticalness. The Fuel level height in the float bowl affects full throttle/low rpm and, also, richness or leanness at cruise/low rpm.
     Reference: a bike that runs cleanly at small throttle openings when cold, but starts to show signs of richness as it heats up to full operating temperature, will usually be leaned out enough to be correct if the fuel level is LOWERED 1mm. Check out and RESET all: Suzuki (all), Yamaha (all) and Kawasaki (if low speed problems occur). Needless to say, FUEL LEVEL IS EXTREMELY IMPORTANT!!!
     If there are low-end richness problems, even after lowering the fuel level much more than 1.5mm from our initial settings, check for needle wear and needle jet (part of the emulsion tube). See Worn Needle and Worn Needle Jet diagram. It is VERY common for the brass needle jets (in the top of the "emulsion tube") in 36mm, 38mm and 40mm Mikuni CV carbs to wear out in as little as 5,000 miles. Check them for "oblong" wear - the needle jet orifice starts out round! Factory Pro produces stock replacement needle jets / emulsion tubes for 36mm and 38mm Mikuni carbs. Click here

     4. Idle and low rpm cruise
     Fuel Screw setting (AKA mixture screws)
     There is usually a machined brass or aluminum cap over the fuel screws on all but newer Honda. It's about the diameter of a pencil. Cap removal details. Newer Honda carbs have no caps, but use a special "D" shaped driver, usually supplied in the carb recal kit. We do have them available separately, too. 800 869-0497 to order -
     Set for smoothest idle and 2nd gear, 4k rpm, steady state cruise operation. Set mixture screws at recommended settings, as a starting point. For smoothest idle, 2nd gear 4000 rpm steady state cruise , and 1/8 throttle high rpm operation. (pj tuning information)
     Pilot fuel mixture screw settings, float level (but, you've "fixed" the fuel level in Step 3 - which you have already done!) AND pilot jet size are the primary sources of mixture delivery during 4000 rpm steady state cruise operation.
     If lean surging is encountered, richen mixture screws (turn out) in 1/2 turn increments. Alternative pilot jets are supplied when normally required.

     Pilot fuel mixture screw settings, float level and pilot jet size also affect high-rpm, 0 to 1/8 throttle maneuvers. Too lean, will cause surging problems when the engine is operated at high rpm at small throttle openings! Opening the mixture screws and/or increasing pilot jet size will usually cure the problem.

     NOTE: A rich problem gets worse as the engine heats up.
     If the throttle is lightly "blipped" at idle, and the rpm drops below the set idle speed, then rises up to the set idle speed, the low speed mixture screws are probably set too rich: try 1/2 turn in, to lean the idle mixture.

     NOTE: A lean problem gets better as the engine heats up.
     If the throttle is lightly "blipped" at idle, and the rpm "hangs up" before dropping to the set idle speed, and there are no intake leaks and the idle speed is set at less than 1000 rpm, the mixture screws are probably too lean: try 1/2 turn out, to richen mixture. Be sure there are no intake leaks and the idle speed is set at less than 1000 rpm!

     Carb Kit Design is a combination of science, art, intuition and and at times, a fair dose of wizardry. There is no dyno that "tells" one how to assemble or modify the carb to deliver proper power and response.
     Perfect Carb Kit TUNING requires patience and perseverance and "reasonable" feel to feel the changes - of which - most motorcycle riders have a good ability to do.
    When a dyno "operator" says he/she has to ride the bike after dyno tuning to do the final tune for cruise smoothness - that's what they are doing. Avoid any dyno operator who says that they don't have to do that!!!
    The only dyno that I know of that will duplicate and visually display the engine smoothness is the EC997 dyno (yes, I know, we make it) - that's one reason why, if you can, you'd like to use one for tuning - a smoother engine IS getting the best mixture. Other dynos claim to "tune to an "A/F Ratio" - probably the biggest marketing scheme in the dyno industry at this time - and they never can equal the quality of tune as designed -
    These tuning kits have been thoroughly tested to ensure easy, trouble-free, optimized performance.

     Please note: If you have installed the kit and gone through the optional screw settings, clip positions and main jets, and still have a persistent flat spot/problem, we ask you to call us. Unique engine / exhaust / filter / altitude / temperature combinations may require individualized setups. We are here to help. The information gained to your solution will be installed in our computerized reference database. PLEASE CALL!
     We ask that upon completion of installation and tuning, that you call us with specifications of your installation, (pipe brand, filters, advancer, altitude, humidity, temperature and final carb settings) to be entered in our TUNING DATABASE. The database allows us to include the "most used" jet sizes and setup specifications in every kit.
     Use (415) 491-5920, (800) 869-0497 or fax (415) 492-8803.

    Thanks!

    Marc W. Salvisberg
    John
    KTM Duke 690

  12. #12
    Junior Member BrianShaw's Avatar
    Join Date
    Apr 2013
    Location
    Aurora, CO
    Posts
    41

    Re: Running Rich, Carbureted 98 ZX6R

    Excellent writeup, Thanks.
    1998 Kawasaki ZX6R
    1973 Honda CL350 Cafe
    sold- 1978 Honda CB750 SuperSport
    sold- 2004 BMW R115R

  13. #13
    Member Davy4575's Avatar
    Join Date
    Sep 2009
    Location
    Elizabeth (kind of)
    Posts
    58

    Re: Running Rich, Carbureted 98 ZX6R

    I raced a 97 zx6R my first two seasons. I ran enormous jets in it, full exhaust and never had rich problems with it. however...It had headwork done on it, and had velo stacks. There is a center baffle in the airbox that needs to be cut out and replaced with a screen. Also, the ram air tubes absolutely have to be connected properly and free from blockages. I was inside my carbs routinely as the bike sat for 7 years before I got it back to life.

    That being said, kawiforums have a wealth of information on it, and some really cool mods for it. but i would suggest reading up on how the carbs work in general and the settings on em. Mains only really hit from upper mid throttle to wfo. needle and clip circuit hit 1/4 to mid throttle (most of your street riding) and pilot is off idle to 1/4 throttle. the three circuits overlap some.

    Id try some basic diagnosis to see if it is even running rich before just assuming it is though.

    If it is indeed running rich across all 3 circuits of the carbs and theyre in sync, it may be something else causing the problem. The first thing that comes to mind is valve adjustments. pretty common for the bike to not start at all as the valves tighten up. Also simple stuff, the 97-99 were notorious for blowing the fuel petcock, I went through 3 on mine. Would leak gas all over, thus the smell, also replaced the fuel pump and there is a vac hose on that rack of carbs in the center of it that has to be connected to the airbox, mine ran like shit without it connected.

    I believe i may have a shop manual around for that bike and a bunch of supplemental material on the carbs. when that thing is running right, it will run like a raped ape. That motor was a tough motor for sure and I had a blast with mine.
    Slow and stupid....at least its entertaining to watch.

    03 R1 Limited Edition (Satanic Edition)
    00 R6 Racebike

    MRA # 420
    Rocky Mountain Photos, DBA Construction LLC

  14. #14
    Junior Member BrianShaw's Avatar
    Join Date
    Apr 2013
    Location
    Aurora, CO
    Posts
    41

    Re: Running Rich, Carbureted 98 ZX6R

    I was unable to get the carbs off but did go through all the vacuum lines and air lines again. Pulled them apart made sure everything was secure. Cleaned the airfilter that goes do the carbs, seperate from the Airbox. Seemed to run better this morning, but I will know more on my ride home. Considering the Kleen Mod and retune the carbs.
    1998 Kawasaki ZX6R
    1973 Honda CL350 Cafe
    sold- 1978 Honda CB750 SuperSport
    sold- 2004 BMW R115R

  15. #15
    Member
    Join Date
    May 2011
    Location
    Hampden & Wadsworth
    Posts
    136

    Re: Running Rich, Carbureted 98 ZX6R

    Anyone know who or where to take a 99 9r I just bought?The bike takes forever to rev, stumbles low medium and has no top end.
    If I keep it pinned it tops out at 125.
    The oil was very low and old.
    I took the bowels off but after running Seafoam they were pretty clean. Think the carbs/throttle bodies are out of sync. Any help much appreciated.

  16. #16
    Senior Member FZRguy's Avatar
    Join Date
    Feb 2003
    Location
    Lakewood
    Posts
    4,476

    Re: Running Rich, Carbureted 98 ZX6R

    If anyone can help with a bowel issue, it's Jim at TFOG.

    http://www.tfogwheelsports.com/
    John
    KTM Duke 690

  17. #17
    Member
    Join Date
    May 2011
    Location
    Hampden & Wadsworth
    Posts
    136

    Re: Running Rich, Carbureted 98 ZX6R

    Thanks JD. :-)

  18. #18
    In A Land Far Far Far Away Lifetime Supporter
    Join Date
    Mar 2009
    Location
    Elwood, Indiana 46036
    Posts
    449

    Re: Running Rich, Carbureted 98 ZX6R

    Quote Originally Posted by FZRguy View Post
    If anyone can help with a bowel issue, it's Jim at TFOG.

    http://www.tfogwheelsports.com/
    Αφροδίτη

    https://www.facebook.com/dcbk.stanley

    The one in the back still catching up....

Similar Threads

  1. Running pig rich
    By Speedwagon in forum Bike Tech
    Replies: 12
    Last Post: Sun Jan 25th, 2009, 01:05 AM
  2. New LED running lights are dim as hell...
    By Aracheon in forum Bike Tech
    Replies: 1
    Last Post: Sat Feb 23rd, 2008, 06:43 PM
  3. Running Rich - Bad Gas mileage
    By McVaaahhh in forum Bike Tech
    Replies: 0
    Last Post: Wed Jul 20th, 2005, 05:26 PM
  4. 84' GPZ750; too rich.. help please
    By japrules in forum Bike Tech
    Replies: 9
    Last Post: Sun Mar 28th, 2004, 02:02 PM
  5. Running Lean
    By CSUAdam in forum Bike Tech
    Replies: 6
    Last Post: Thu May 29th, 2003, 03:10 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •